EN
www.mobotix.com
Innovations– Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high-resolution video
systems cost-ecient.
MOBOTIX AG • Security-Vision-Systems • D-67722 Langmeil • Phone: +49 6302 9816-103 • Fax: +49 6302 9816-190 •
[email protected]PTMount Quick Install
Security-Vision-Systems
31.988_EN_V1_07/2014
PTMount for MOBOTIX S15D
Sensor Modules
Manually adjustable dome mount for one MOBOTIX sensor
module housing S15D/S14D (not included), freely turning
along three axes,
for wall, ceiling and upright installations
• S15D: Modular PoE network camera with max. two sensor modules for con-
cealed installation (not included)
• All components weatherproof (S15D: IP65, sensor modules IP66),
–30 to +60°C/–22 to 140°F
• Day and Night sensor modules can be freely combined
• Sensor module connection cables max. 2m each (e.g., for indoors/outdoors)
MOBOTIX S15D
with 2 sensor modules, each in
PTMount
MX-PTMount-OPT
Standard Delivery
1.1
1.2
1.9
1.3
1.4
Item Count Part Name
1.1 1 Sphere with freely rotating insert (installed)
1.2 1 Foot (installed)
1.3 1 Base plate (installed)
1.4 1 Swivel ring (installed)
1.5 1 Sealing
1.6 4 Washer Ø 4.3mm, stainless steel
1.7 4 Wood screw 4x40mm, stainless steel
1.8 4 Screw anchor S6
1.9 1 Allen wrench 2.5mm
Preparatory Steps
• Using the supplied Allen wrench, re-
move the two screws that hold the
foot onto the swivel ring.
• Remove the swivel ring and the base
plate.
•
Make sure that there is enough space
for installing the PTMount and that
you can access it from the rear later
on. The surface should be even and
smooth so that the sealing lies flat
properly.
•
Drill the holes for the base plate (drilling
template see
Section «Dimensions/
Drilling Template»
).
•
In the center of the drilling template, drill
another hole into the wall or faceplate
for the sensor cable. Since you will
push the hinged ferrite through this
hole later on, the hole should have
a diameter between 15 and 35mm.
•
Insert the screw anchors into the holes,
if required.
104mm
Installation of PTMount and Sensor Module
• Hold the sealing, the swivel ring and
the base plate as shown in the figure.
• Attach the base plate using the sup-
plied wood screws and washers.
• When tightening the screws, make
sure that you can still rotate the swivel
ring by hand.
• Carefully guide the sensor cable
through the sealing, the swivel ring
and the base plate, then attach the
hinged ferrite to the cable.
• Push the sensor cable into the wall/
ceiling so as to completely hide the
ferrite.
•
Guide the sensor cable from the back
into the foot and the sphere.
• Use the two screws to ax the foot
and sphere assembly to the swivel
ring and make sure that the foot can
still be rotated.
• Loosen the two fastening screws of
the insert (
1), then rotate the insert
so that the small bar opposite of the
TOP/OBEN label points to the hole of
the grub screw (2).
• Secure the insert against rotating by
tightening the two fastening screws.
• Attach the sensor module cable to
the sensor module (turn blue bayonet
catch to the left and remove, pull out
the plug, connect the sensor cable,
apply bayonet catch and lock by turn-
ing to the right).
• Push the sensor module into the
PTMount so that the MOBOTIX let-
tering is turned 90 degrees to the left
vs. the TOP/OBEN lettering.
•
Using the module wrench (red or black),
lock the sensor module by turning it
90 degrees to the right.
•
Secure the sensor module by tighten-
ing the grub screw using the supplied
Allen wrench. The grub screw locks
the sensor module within the insert
and prevents inadvertent unlocking
of the sensor module.
•
Adjust the sensor module temporarily
by pointing it into the desired viewing
direction.
• Make sure that the TOP/OBEN label
on the insert is pointing upwards. If
this is not the case, loosen the two
fastening screws and rotate the insert.
Lightly tighten the two fastening screws.
Continue to bring the camera into service as described in
Section «Initial
Operation S15D with PTMount»
.
Max.
10cm/4in!
2
M
O
B
O
T
I
X
T
O
P
O
B
E
N
M
O
B
O
T
I
X
T
O
P
O
B
E
N
360°
360°
100°
M
O
B
O
T
I
X
T
O
P
O
B
E
N
1.5
1.8
1.7
1.6
Adjustable Along Three Axes
360°
Panning
360°
Rotating
100°
Tilting
Flexible Installation
Mounting to a Ceiling
Mounting upright
Mounting to a Wall
Weatherproof (IP66)
–30 to +60°C/–22 to 140°F
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels